Agio-international Sling Swivel-Rocker User Manual download pdf

Page 2

IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!

TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT

"U" BAR

"U" METAL

PLATE

BOLT

PVC BOLT

COVER

SPRING

WASHER

NUT

NOTE: MAKE SURE ARROWS

FROM BOTH THE "U" BAR

AND ROCKER ASSEMBLY

ARE POINTING IN THE

SAME DIRECTION!

SEAT DESIGNS MAY

VARY BUT THE ASSEMBLY

IS THE SAME

Step 1: Identify all parts packed in carton against the parts list. Remove all protective materials.

Place parts on a non-abrasive surface to avoid scratching. If you are missing any parts or are

unsure as how to proceed with the assembly, call our Customer Service Center at

1-800-416-3511. Do not attempt assembly if any parts are missing or damaged.

Step 2: Place the swivel base (with rocker assembly) on a flat, solid surface. Make sure the rocker

assembly is positioned all the way into the base. It may have shifted or vibrated out during

shipment.

Step 3: Important: We recommend 2 people work together to assemble the chair. Note the

arrow labels on the "U" bar and the rocker assembly. Also note the horseshoe shape of the

rocker plate. Point the open end of the horseshoe away from you. The arrows on the rocker

assembly should be pointing towards you. Set the chair frame on the rocker assembly with

front of the seat facing you and the arrows on the "U" bar pointing towards you as shown

in Figure 1. This is very important for a safe, balanced rocking motion. If chair frame has

been properly positioned on the rocker assembly, all arrows on the "U" bar and rocker

assembly will be pointing in the same direction.

Step 4: Critical Step: The "U" metal plates must be installed in the proper location. Read this

step and carefully examine. Insert the "U" metal plate, so that the "U" bar and rocker plate

are between both sides of the "U" metal plate. Make sure that the holes in the "U" metal

plate are completely aligned with the holes in the "U" bar as shown in Figure 1. Guide the

bolts through the holes on the top side of the "U" metal plate, through the holes in the

"U" bar portion of the chair, through the holes in the rocker plate and then, most importantly,

through the holes in the bottom side of the "U" metal plate. It is very important that the

holes in the bottom portion of the "U" metal plate be placed directly beneath the holes in the

rocker plate. Add a spring washer and a nut to each bolt as shown in Figure 2. Hand

tighten nuts 3-4 revolutions only. Repeat the same procedure on the other side.

CAUTION: Failure to place "U" metal plates under the rocker plates and above the

"U" bar exactly as shown in diagram will cause the bolt heads and nuts to damage the

structure of the rocker plates and the "U" bar. Damage due to over tightening of bolts

or improper assembly could cause injury and may void your warranty.

Step 5: Tighten all nuts and bolts with the hex wrenches provided. Do not over tighten. Remove

arrow labels from "U" bar and rocker assembly. Cover bolts with PVC bolt covers.

Step 6: Your chair should be ready for use. If your chair is not rocking properly, double-check your

assembly procedure, especially Step 3. If the chair rocks too far forward to or is difficult to

rock backwards, you have probably installed the seat frame backwards on the rocker

assembly. If you need further assistance, please call our Customer Service Center

at 1-800-416-3511.

IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or

improper assembly is not covered under our warranty. Please read all instructions carefully

before assembly. If you have any questions regarding your assembly, call our Customer

Service Center at 1-800-416-3511.

Figure 1

Figure 2

"U" BAR

FRP

ROCKER

ASSEMBLY

QTY

SWIVEL BASE &

ROCKER

ASSEMBLY

5/16" X 40 MM

BOLT

E8.0 X 2.3 MM

SPRING WASHER

HW0003

5/16" NUT

HW0015

"U" METAL

PLATE

CHAIR FRAME

PARTS LIST DESCRIPTION ORDER PART #

HW0295

HW0296

50-49661-1

QTY

PARTS LIST DESCRIPTION ORDER PART #

PVC BOLT COVER

HW0028

FOOT CAP

FACTORY ASSEMBLY

HEX WRENCH-1

HW0008

HEX WRENCH-2

HW0007

FRP

FACTORY ASSEMBLY

G0009

FC0004

SWIVEL BASE

FOOT CAP

SLING TUBE CAP

FACTORY ASSEMBLY

FC0046

PVC BOLT

COVER

AR1094

AR1095

50-49661-1 1

Summary of Contents

Page 1 - 50-49661-1

Page 2IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANT

Comments to this Manuals

No comments

Agio-international Sling Swivel-Rocker User Manual

Browse online or download User Manual for Furniture Agio-international Sling Swivel-Rocker. Agio International Sling Swivel-Rocker User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Furniture Agio-international Sling Swivel-Rocker